Description:

The unfiltered liquid is fed into the filter under positive pressure, where liquid travels in downwards direction and finds its way through opening on sides of the Filter Plates. As the liquid pressure increases, the Filter media holds the foreign particles and allows only clear filtrate to pass through the central channel formed by interlocking pressure cups to the outlet. Filtration is continued until the cake holding capacity of the unit is reached or until the filtrate rate becomes too slow owing to cake resistance.
 

Horizontal Plate Filter Press is enclosed construction, preventing evaporation, oxidation, leakage and fumes escaping from product.
Filter plates are available in two sizes. Deep plate for large percentage of cake holding capacity and Shallow plate for small percentage of cake holding capacity.
The horizontal filter plate and even thickness of cake, prevents the cake dropping as well as cracking, thus assuring better filtrate quality.
The Filtration area and cake holding capacity can be increased or decreased according to requirement.

Technical Details: :

Types Diameter of Plate No. of Plates Filtering Area M2 Cake Holding Capacity Ltrs. Capacity Ltr / Hr
SB 8x6 8" 6 0.198 4.50 400
SB 8x8 8" 8 0.254 5.78 500
SB 14x8 14" 8 0.756 27.00 1500
SB 14x10 14" 10 0.924 35.00 1800
SB 18x8 18" D 8 1.270 51.00 2500
SB 18x15 18" S 15 2.270 44.00 4500
SB 18x12 18" D 12 1.840 78.00 3700
SB 18x23 18" S 23 3.400 65.00 6800
SB 24x12 24" D 12 3.430 148.00 6700
SB 24x23 24" S 23 6.336 120.00 12600
SB 33x7 33" D 7 4.000 175.00 8000
SB 33x14 33" S 14 7.500 210.00 15000

The values of "Flow-Rates" mentioned in technical specifications have been estimated for the following operating parameters:

Description:

The Cartridge assembly consists of plates, perforated screens, spacers and fitter media. Interlocking spacers internally form single pipeline. The unfiltered liquid is centrally fed under pressure from bottom inlet. The liquids spreads out equally on each plate fitted with filter media. Solids remain on filter media and clear. filtrate flows through precisely made holes on sides of plates and collects in the shell, which then comes out through the outlet. In this process, solids are evenly distributed on each plate. The cake is then cleaned from the filter material and used again for filtration process.
 

Single pass filtration with no solid bypass
Full batch recovery, no separate scavenging system needed.
Proper sealing which allows the filtration of volatile, toxic and inflammable products.
Plate pack arrangement ensures :
Any type of filtering media singularly or in combination can be used to achieve required micron efficiency.
Easy removal and cleaning of the Cartridge Assembly.
Closed System ensures :
Filtration of toxic, hazardous, explosive materials.
Efficiently cleaned and sterilized.
Central feeding ensures
No solid inside the vessel, complete recovery of liquids.
Cake solids can be maximum dried with N2
Complete cake retains over the plate.
Uniform filter-aid bed can be formed.
Reduces the cost of expensive solvents.

Optional Available:

Built In Stirrer Arrangement with Lifting and Lowering Device.
Steam Fittings with All Connections Factory Fitted.
Non Tilting Type With Bottom Discharge Models Are Also Available.
Capacities Available: From 10 Ltrs to 2000 Ltrs Capacity.

Functions:

Basically this unit is used for preparation of starch paste. Hemispherical shape ensures that the heating of the starch paste is uniform and gets more surface area. The tilting type arrangement ensures ease in unloading the paste into any container or vessel. The starch is put in the kettle and water is added till desired thickness is achieved. The kettle is jacketed and is heated till the starch melts and a thick paste is achieved. This paste can be agitated either manually or with the help of an anchor type agitator which will constantly stir the paste so that there will no lumps formation and proper mixing is achieved. Temperature can be set to desired temp by adjusting the thermostat provided and the temperature can be seen in the dial thermometer provided.
 

Salient Features:

Entire construction in Stainless steel
Semi hemispherical bowl ensure that entire bowl can be emptied by rotating the worm wheel.
Simplified construction enables ease of operation.
Steam or electric heating is possible depending upon the user requirements.
When used with stirrer / anchor the movement of anchor is forward and reverse using cyclic timer. Stirrer can be supplied at additional cost.

When supplied with stirrer, there is a top entry drive without using any "V" belt. Stirrer can also be removed for cleaning. Temperature indication is possible at additional cost.

Technical Details: :

Types

Diameter of Plate

No. of Plates Filtering Area M2 Cake Holding Capacity Ltrs. Capacity Ltr / Hr
SB 8x6 8" 6 0.198 4.50 400
SB 8x8 8" 8 0.254 5.78 500
SB 14x8 14" 8 0.756 27.00 1500
SB 14x10 14" 10 0.924 35.00 1800
SB 18x8 18" D 8 1.270 51.00 2500
SB 18x15 18" S 15 2.270 44.00 4500
SB 18x12 18" D 12 1.840 78.00 3700
SB 18x23 18" S 23 3.400 65.00 6800
SB 24x12 24" D 12 3.430 148.00 6700
SB 24x23 24" S 23 6.336 120.00 12600
SB 33x7 33" D 7 4.000 175.00 8000
SB 33x14 33" S 14 7.500 210.00 15000

The values of "Flow-Rates" mentioned in technical specifications have been estimated for the following operating parameters:

Fluid : Water
Insoluble : Carbon
Filter media: Non-woven polypropylene cloth of 418 grades.
Carbon loading: 5 Kg/m2 filtration area

Description:

"Bhagwati" starch paste kettle will be made out of SS 304 rectangular pipes of 3 mm the and will be an independent resting type frame work where no foundation will be required. The kettle will be a hemispherical type bowl with either steam / oil / water heating jacket will be provided. The kettle will be manufactured from 2.5 mm the SS 304 sheet and the jacket will be of 2.5 mm mild steel (in case of steam jacket the thickness will be 4 mm). There will be oil / water heated fitted at the back bottom side of the kettle. The kettle will be having a worm type arrangement for tilting. A temperature controller and a temp indicator will be provided for temp control and indication. The kettle will be insulated with 50 mm the glass wool insulation and cladded with 16 SWG SS 304 sheet. Kettle will be buffed to 150 grit matt finishes externally and internally the kettle will be buffed to 220 grit mirror finish.

Optional Available:

Built In Stirrer Arrangement with Lifting and Lowering Device.
Steam Fittings with All Connections Factory Fitted.
Non Tilting Type With Bottom Discharge Models Are Also Available.
Capacities Available: From 10 Ltrs to 2000 Ltrs Capacity.

Functions:

Basically this unit is used for preparation of starch paste. Hemispherical shape ensures that the heating of the starch paste is uniform and gets more surface area. The tilting type arrangement ensures ease in unloading the paste into any container or vessel. The starch is put in the kettle and water is added till desired thickness is achieved. The kettle is jacketed and is heated till the starch melts and a thick paste is achieved. This paste can be agitated either manually or with the help of an anchor type agitator which will constantly stir the paste so that there will no lumps formation and proper mixing is achieved. Temperature can be set to desired temp by adjusting the thermostat provided and the temperature can be seen in the dial thermometer provided.
 

Salient Features:

Entire construction in Stainless steel
Semi hemispherical bowl ensure that entire bowl can be emptied by rotating the worm wheel.
Simplified construction enables ease of operation.
Steam or electric heating is possible depending upon the user requirements.
When used with stirrer / anchor the movement of anchor is forward and reverse using cyclic timer. Stirrer can be supplied at additional cost.

When supplied with stirrer, there is a top entry drive without using any "V" belt. Stirrer can also be removed for cleaning. Temperature indication is possible at additional cost.

Technical Details: :

Out Put

2,00,000 Tablet/Hour

Power Supply 220 volts, single phase ,50cs,1AMP
Passage Size 50 MM
Tablet Travel /Time 3000 MM distance for 20 to 60 seconds. (Depending on fluidity and vibrations)
Min / Max. Tablet Dia 5 mm / 40 mm
Extraction 80.250 M³/H at approx. 100 mm column of Rheostat
Dimension 360 mm dia. X 870 to 1040 mm Height.
Net Weight 30 Kgs.

Description / Specification of De Duster

We are involved in offering a wide range of De Duster to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of  De Duster. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design 

Salient Features:

Roll Compactor RC 200/50 & 200/75 are G.M.P models. Totally enclosed with SS304 cladding and framework ease of cleaning.Very Compact Design available in plain water-jacketed or flame proof model.
 

Screw is driven through variable drive safety sleeping clutch between gearbox and feed screw.
Rolls drive through twin shaft gear box with speed drive unit coupled to it using a flexible coupling which ensures synchronizations of the roll with a steady torque loading.
Feeding device and sealing of roll by means of check plates and all parts that are exposed to wear are made of hardened steel. The compacting head is two piece assemblies for easy dismantling.
Pre-densities screw comprises of cylinder or conical shape, which is well polished and made of AISI SS-304 quality material.
Compacting rolls sleeves are made out of tool steel, hardened to 55 HRC approx., & are keyed into shaft & thus protected against axial slipping by thrust plates & bolts.
The feed screw assembly can be hydraulically lifted by hand - operated hydraulic pump. This facilitates ease in cleaning.
Scrapper Assembly so designed to dismantle for ease of cleaning.
Pre-Compression chamber guides the powder without any slippage or leakage.
The main roll drive & feed screw are electrically interconnected.
All controls and indicators of the compactor are permanently built-in namely, on/off rolls, on/off feeds screw, main switch forward / reverse switch, ammeters for rolls & feed screw & emergency stop.

Technical Details: :

Model No.

200/50 GMP

200/75 GMP
Out/Put depending on the material to be compacted 20 to 60 Kgs/hour 30 to 100 Kgs/hour
Roll Size 200mm Dia x 50mm 200mm Dia x 75mm
Roll Speed (step pulley drive) 6 to 25 RPM 6 to 25 RPM
Feed Screw Speed. (variable speed drive) 10 to 60 RPM 10 to 60 RPM
Roll Drive Motor. 5 HP,960 RPM, 440
volts, 3phase, 50Hz 5 HP,960 RPM, 440
volts, 3phase, 50Hz
Feed Screw
Drive Motor. 1HP, 1440 rpm, 440
volts, 3 phase, 50Hz 1HP, 1440 rpm, 440
volts, 3 phase, 50Hz
Over all Dimensions mm 975 x 1150 x 1700 (H) 975 x 1150 x 1700 (H)

Salient Features:

Provided with stainless steel dust collection tray and inlet connectors.(This can be provided in M.S also for cost reduction)
Blower fan is dynamically balanced and the unit is with castor wheels.

Technical Details: :

Suction Capacity

150 CFM (250M³/HOUR)at 70mm W.G.

Filtration Area 9 Sq. Ft.(0.8m²)
Dust Storage Cap. ¾ Cu. Ft.(0.21M³)
Intel Connections 5 nos. of Dia 1½" (38.1mm)
Electrical Motor of 1 H.P,2800 RPM,440 V,50 CS, 3 Ph.
Dimensions 28 " X 19" X 32" (HT)
Net Weight (Approx) 80 Kgs.
 

Application:

Vibro separators are circular unitary gyratory screens used to separate mass composition of solids from solids, liquid from solid and for gradation of materials as per particle size, having a very wide range application. This is accomplished by vibrating the screens in three different planes along the vertical axis by means of a specially designed vibratory motor having off cantered weights at the top and bottom end of the motor shaft. The top weight causes vibration in the horizontal plane which causes the material to move across the screen towards the periphery. The lower weight acts to tilt the machine which causes vibration in the vertical tangential axis. The angle of lead of the lower weight with relation to the upper weight provides variable control of the screening pattern. Thus the material moves across the screens and also in the vertical and tangential planes enabling maximum screening.

"BHAGWATI" Vibro sifter are available with a wide range of possible screen sizes (mesh) Option for multiple deck separation is also possible. The unit consist of Specially designed vibratory motor to run on 400/440V, suitable HP, 3 phase, 50 cycles electric supply ,with adjustable eccentric weights at the top and bottom of the motor shafts mounted vertically at the center of the base plate of screening unit. Screening unit consists of SS 304 screen sandwiched between SS 304 hopper and bowl with the help of special clamp with gasket. This in turn is clamped to the base plate. Rugged Springs placed over the circular motor base amplify the vibration and at the same time restrict the vibration from being transferred to the floor.

Technical Details: :

Model No.

SBVS-20

SBVS-30 SBVS-36 SBVS-48 SBVS-60
Output kg / hour 50 to 200 75 to 300 100 to 400 125 to 500 150 to 800
Screen Diameter 500 mm 750 mm 915 mm 1220 mm 1524 mm
Charging height 1190 mm 1190 mm 1190 mm 1330 mm 1250 mm
Discharging height 750 mm 750 mm 750 mm 700 mm 740 mm
Electric Power hp/kw 0.5 / 0.3 0.5 / 0.3 0.5 / 0.3 1 / 0.75 2 / 1.5

Note: Dimensions & Technical Details are subject to change as per customers' requirement without any further notice.

Application:

Pan: SS 316 semi ellipsoidal size pan with a circular mouth for charging & discharging of tablets Pan mounted at an inclination of 45 degrees to the horizontal.
Drive Assembly: Consists of a suitable 1 HP 3 Phase, 440 V, and 1440-RPM TEFC motor with suitable worm reduction gearbox and cone pulley arrangement to give three-speed output.
Hot Air Blower: The unit is provided with a hot air blower consisting of suitable HP 3 Phase 440 V, 2880-RPM TEFC electric motor & centrifugal blower with damper delivering required CFM. The air is heated by means of suitable electric heater to give air at 30 to 90 degrees Heater with thermostat control and flexible hose pipe.
Control Panel: Unit provided with suitable control panel with starters and push button to actuate the drive and for blower The circuits consists of MCCBs, relays and contractors in series Ample overload protection is provided by the MCCB and the relay Wires coming out of the connections are numbered for easy recognition
Mounting: The motor and gearbox is mounted inside sturdy MS frame and the pan mounted on the Gearing housing fitted in the stand. Blower mounted by the side of the stand or placed in remote location if required.
Finish: All joints argon Arc welded and all SS Parts polished to suitable finished required of pharmaceutical equipment MS parts painted to smooth finish.
Options Available
a.Unit with FLP motors and FLP push button station but non FLP panel to be mounted outside FLP area. b. Steam heating for blower.

Technical Details: :

Model No.

SBCP-24"

SBCP-36" SBCP-48" SBCP-72"
Loading capacity 25 Kgs 60 -80 Kgs 100-120 Kgs 200-250 Kgs
Drive Motor HP 3 PH 50 C S 415 V AC line 0.5 HP 1.00 HP 2.00 Hp 7.5 HP
RPM of Pan (empty) 12/24 12 / 36 10 / 30 5 /10
Hot air blower motor HP 3 PH 50 C/S 415 V AC line 0.50 0.50 1.00 1.00
Blower capacity Maximum CFM 100 200 500 750
Heater KW 1.5 Kw 3 Kw 4.5 Kw 6 Kw

Description:

Planetary Mixer: This equipment is basically a mixing assembly where the agitation pattern is of the planetary nature the beater or the agitation assembly rotate around itself as well as travel in a circle in the bowl thereby achieving intimate mixing. Because of special design feature of shifting the mass is uniformly and intimately mixed. The unit consists of Bowl SS Cylindrical bowl with spherical dished bottom with inside surface polished to smooth finish. MS Jacket on cylindrical and spherical area to operated on 3 Kg / cm sq. Steam pressure Complete with steam inlet and cold water inlet and outlet connections with standard fitting like pressure gauge, vent cock, release valve and drain. Bowl also suitable for vacuum application and fitted with 3 nos. Of castor wheel, two fixed and one swivel type. Suitable locking lugs for fixing bowl to the machine. 

Top Dish: SS top dish for covering the bowl with SS flange having groove for fixing the sealing gasket. Necessary connection with serrated nozzle provided for connecting flexible pipe for vacuum application Light and sight glasses suitably provided. 
 

Agitator Assembly:

1 / 2 No/s. Of SS open type Beaters.
1 No. SS Scrapper fitted with PTFE strip on both sides.
1 No. centrally located High Shear Emulsifier. (optional)

Agitator Assembly:

1 / 2 No/s. Of SS open type Beaters.
1 No. SS Scrapper fitted with PTFE strip on both sides.
1 No. centrally located High Shear Emulsifier. (optional)

Drive Mechanism for Beater:

Suitable HP 1440/2880 RPM DUAL Sped TEFC Motor to work on 415 V, 50 c/s 3 Phase AC supply line, mounted on MS plate.
Worm reduction gear box coupled to the motor through belt and pulley arrangement.
Epicyclical gear box coupled to the motor through belt and EPICYCLIC gear train arrangement to achieve planetary motion.
Suitable HP 1440 RPM TEFC motor to work on 415V 3 phase 50 C/s AC supplies line for High Shear Emulsifier. (Optional)
The above items are assembled on the top plate which is supported on a Cast iron sliding sleeve with MS gussets.

Main Body: MS column with flange mounted on stool base 2 nos limit switches provided at upper and lower limits of the column to control traverse of the sleeve.

Lifting Arrangement of the Drive Assembly (Mechanical):

Consist of 

Suitable HP, 1440 RPM motor working on 415V 50 c/s 3 Phase AC supply line.
Worm reduction gear box coupled to the motor through belt and pulley arrangement.
MS STOOL for mounting the reduction gear unit.

Lead screw and guide bar to guide up and down traverse of the drive assembly.

Lifting Arrangement Hydraulic:

Horse shoe base with suitable gun metal bush housing for 3nos chrome plated guide bars with suitable retaining plate and supports.
Hydraulic Power pack assembly complete with Tank, suitable HP pump with filter connected to suitable solenoid valve arrangement with control and check valve for preventing drop age of pressurized fluid.
Power Pack connected with fixed / flexible high pressure inter connecting hose to hydraulic cylinder of suitable lift clamped to the drive head to give smooth up and down traverse.
Limit switch for controlling up and down traverse motion.

Control Panel:

Air break DOL dual speed starter with DOL relay for main motor.
HRC back up fuses.
Ammeters for main motor and lift motor.
Push Button actuator for above operation fitted on control panel.
The circuits consist of MCBS, relays and contactor is series. Ample overload protection is provided by The MCBs and the relay.
Wires coming out of the connections are numbered for easy recognition.
Finish All SS parts polished to smooth pharmaceutical finish. All MS part painted to smooth finish.

Options Available:

Unit with FLP motors and FLP push button station but non FLP panel to be mounted outside FLP area

Jacketed bowl for steam / electrical heating

Description:

We offer heavy duty Mass Mixer that is mainly used for the purpose of homogeneous mixing of different substances or materials. The Industrial Mass Mixer that we supply in the market is effectively used for mixing various kinds of thick and heavy materials. The safety gland of the Powder Mass Mixer prevents ingress of external powder into the trough and it also guard against any kind of leakage. In addition to this, these mixers are very endurable and easy to operate. Further, the company is counted as a major mass mixer Manufacturer and one of the prime Suppliers in the market.

Shell: Consisting of 'U' trough of suitable dimensions. Construction of S.S. and side plates duly M.S. stiffened from outside and from inside with S.S.

Mixing Mechanism: Paddle type blades welded to the main shaft provide for efficient mixing of thick heavy material. PTFE gland mechanism provided at shaft ends prevents ingress of external powder into the trough and prevents leakage.

Charging: From the top charging can be done through a hinge able lid, hopper or Nozzle can be provided for additional spraying of additives.

Discharge: By bottom discharge slide Iris or Butterfly valve of suitable diameter, for regulated discharge.

Drive: Consisting of suitable H.P. TEFC 3 phase ac 415v / 50 cycles motor coupled to suitable worm gear, with driving shafts mounted on suitable Plummer block. Mounting: Mounted on suitable ISMC Section Stand, with protective covers for belts and couplings.

MOC: All contact parts in S.S. Constructions. Complete unit with S.S. cover and all surfaces polished to mirror dull finish. MS parts dull painted to smooth finish.
 

Salient Features:

All contact parts can be easily and quickly dismantled and cleaned.
Machine is designed for continuous operation.
Cylindrical screen for higher output.
Flame proof electrical can be provided at extra cost.

Technical Details: :

Model No. SBMM-50 SBMM-100 SBMM-150 SBMM-200 SBMM-300
Working Capacity-KG (Considering bulk density 0.97 gm/cc) 110 Ltr. 220 Ltr. 330 Ltr. 440 Ltr. 560 Ltr.s
speed of Stirrer 35 RPM 35 RPM 30 RPM 25 RPM 20 RPM
Electrical Motor 3hp / 2.2Kw / 144RPM / 415v / 50 Hz / 3phase 5 hp / 3.7 kw / 144 RPM / 415v /50 Hz / 3 phase 7.5hp / 5.5 kw / 144 RPM / 415v / 50Hz / 3phase 10 hp / 5.5kw / 144RPM / 415v / 50 Hz / 3 phase

15hp/7.4kw/144

RPM/415v/50Hz / 3phase
Over all dimensions in MM 1900x950x1150 1900x950x1150 2350x1000x1500 2475x1000x1500 2650x1050x1600
Net Weight in kgs. 350 Kgs 450 Kgs 550 Kgs 600 Kgs 700 Kgs
Gross weight in kgs 450 Kgs 600 Kgs 750 Kgs 850 Kgs 1000 Kgs